![]() ![]() 0=Alarm only, 1=Alarm and Flip3 Delay Time 10 0 Delay in minutes stored in the T-Max® 3W G2.5 Session Counts 65535 0 Total session counts for T-Max® 3W G2s.6 Lamp Hours 65535 0 Bulb hours for each bed.7 Bed Hours 65535 0 Number of hours a bed is on.8 Manual Session Counts 65535 0 Counts the number of sessions the T-Max® 3W G2 has run while in Stand Alone Mode9 Clean Room 1 1 0 = Clean Room Disabled, 1 = Enabled10* Manual Lockout 1 0 0 = Stand Alone Enabled, 1 = Disabled13 Cool Down Mode 10 0 0 = Disabled, 1-10=Enabled. Repeat Steps 2-4.7) To exit the Parameter mode press and hold the Up and Down buttons together until the period goes away.Parameter Numbers for Observing and Changing Parameters.Parm Description Max Default Notes1 Address 255 254 Address of T-Max® 3W G22 Beep Mode 1 0 Used for High Power beds. You may now changeanother parameter by pressing the Up and Down buttons until the parameter you want displayed. For example, if youare checking lamp hours (Parameter 6) and the display flashes the numbers 53 three times, then 14 three times, pauses then repeats, then thetotal lamp hours stored in that T-Max® 3W G2 is 5314.5) Press the Up or the Down button to change the parameter to the desired value.If you want to clear the value for that parameter, press the Up and Down buttons at the same time until the display flashes “0.0”.6) Press the Start/Stop Button.The display will show the parameter number you just changed and a solid period in the lower center of the display. To display this value, the T-Max® 3W G2 will flash twonumbers-three times, then two numbers-three times, pause, two numbers-three times, two numbers-three times, pause, etc. the value displayed can be as high as 9999. The number shown is the currentvalue for that parameter.For Lamp Hours, Session Counts, etc. 1 (point one).3) Press the Up and Down Buttons until the parameter number that you want is displayed.4) Press the Start/Stop Button to observe the current value for that parameter.The Display will show a number with a period in the lower center of the display. Oncethe buttons are released the display will read a. Keep power removed from the T-Max® Manager or Pro until all parameter changes are complete.1) Apply power to the T-Max® 3W G22) Press and hold the Start/Stop and Up buttons together on the T-Max® 3W G2 until a “P-” appears on the display. ![]() The timer is now ready to be used as a stand alone timer.Setting ParametersNote: If you are using a T-Max® Manager or T-Max® Manager/Pro and multiple T-Max® 3W G2s, remove power from the T-Max® Manageror Pro. ![]() Pressand release the Up button and the flashing 88 will stop. Press and release the Start/stop button and the display will flash 88. Plug thetransformer into a 120VAC outlet.Initial configurationWhen power is first applied to the timer the display may show a 99. If you are not sure which two wires to use, refer to the tanning bed’s manual or contact the tanning bed’s manufacturer.Connect the 9V 300mA transformer to the screw terminal labeled “PWR IN 9-12V” on the back of the T-Max® 3W G2. Two of these wires are specifically used for connecting the tanning bed to anexternal timer. T-Max® 3W G2 User’s GuideSupplied ComponentsSpecifications1, T-Max® 3W G2 Interface Timer Power Supply 9-12 VDC or AC 300mA1, 9VDC or AC Power Supply Dimensions Cover Plate: 5.25” x 5.25”1, T-Max® 3W G2 User’s Guide PCB: 2.5” x 3.25” x 1.5”1, 50’ Modular Cable with RJ-22 connectors on both ends Relay 220V SPSTPhysical ConnectionsConnect the two wires from the tanning bed, for attaching to an external timer, to the “contact” screw terminals on the T-Max® 3W G2.Note: There may be many wires visible on the tanning bed. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |